砂-膨润土混合屏障材料渗透性影响因素研究

建立了一个新的结构-尾流振子耦合模型. 流场近尾迹动力学特征被模化为非线性阻尼 振子,采用van der Pol方程描述. 以控制体中结构与近尾迹流体间受力互为反作 用关系来实现流固耦合. 采用该模型进行了二维结构涡激振动计算,得到了合理的 振幅随来流流速的变化规律和共振幅值,并正确地预计了共振振幅值$A_{\max}^\ast$ 随着质量阻尼参数$\left( {m^\ast + C_A } \right)\zeta $的变化规律,给出了预测$A_{\max }^\ast $值的拟合公式. 采用该模型计算了三维柔性结构在均匀来流和简谐波形来流作用下的VIV 响应. 结构在均匀来流作用下振动呈现由驻波向行波的变化过程, 并最后稳定为行波振动形态. 在简谐波形来流作用下,结构呈现混合振动形态,幅值随时间呈周期变化.     

裂隙岩体渗透系数确定方法研究

裂隙岩体渗透系数以及渗透主方向的确定对研究岩体渗透性大小及各向异性具有重要意义。高放废物地质处置库介质岩体的渗透性能将直接影响其使用安全性。本文运用离散裂隙网络模拟的方法对我国高放废物处置库甘肃北山预选区3#钻孔附近裂隙岩体进行了渗透性质分析。通过对3#钻孔1715～1780m段压水试验数据的反演,标定了离散裂隙网络渗流模型中的裂隙渗透参数(导水系数T)。利用标定的离散裂隙网络模型对场区裂隙岩体进行了渗流模拟,确定了该区域裂隙岩体的渗流表征单元体(REV)的尺寸大小以及渗透主值和主渗透方向。运用离散裂隙网络模型计算得出的渗透主值的几何均值与现场压水试验计算结果较接近,证明了计算结果的有效性。     

基于神经网络的间隙机构运动副磨损预测

应用BP神经网络建立了磨损率与接触应力、滑动速度和材料硬度之间的非线性关系模型,并对该网络模型进行了验证和测试,结果表明,训练良好的神经网络模型能够准确反映样本所蕴含的内在磨损规律,且具有较好的预测效果。基于非线性弹簧阻尼模型和修正的Coulomb摩擦力模型对含间隙曲柄滑块机构进行数值仿真分析,获得间隙机构运动副的接触应力和相对滑动速度,利用训练好的神经网络磨损模型对轴套的磨损进行迭代磨损预测分析,发现随着曲柄转数的增加,轴套表面一些特定位置处的磨损越来越严重,最终导致轴套表面出现非均匀磨损现象,其原因是间隙机构运转过程在一些特定位置处产生了较大接触应力和碰撞力。     

HL-2M 主机线圈冷却系统设计和优化

用一维网络仿真和解析计算方法对HL-2M 磁体TF 线圈、PF 线圈和CS 线圈水冷却系统进行设计和计算,给出了冷却系统工程设计所需要的水力参数。通过优化冷却系统的资用压力和流量分配,得到满足子系统动力输出的最大流量为400m³•h⁻¹,最大压力为1.8MPa,满足线圈在最大流速4.5m•s⁻¹ 下热交换的要求。     

Asymptotic Analysis of an Elasticity Equation for a Finger-Like Hydraulic Fracture

We derive a novel integral equation relating the fluid pressure in a finger-like hydraulic fracture to the fracture width. By means of an asymptotic analysis in the small height to length ratio limit we are able to establish the action of the integral operator for receiving points that lie within three distinct regions: (1) an outer expansion region in which the dimensionless pressure is shown to be equal to the dimensionless width plus a small correction term that involves the second derivative of the width, which accounts for the nonlocal effects of the integral operator. The leading order term in this expansion is the classic local elasticity equation in the PKN model that is widely used in the oil and gas industry; (2) an inner expansion region close to the fracture tip within which the action of the elastic integral operator is shown to be the same as that of a finite Hilbert transform associated with a state of plane strain. This result will enable pressure singularities and stress intensity factors to be incorporated into analytic models of these finger-like fractures in order to model the effect of material toughness; (3) an intermediate region within which the action of the Fredholm integral operator of the first kind is reduced to a second kind operator in which the integral term appears as a small perturbation which is associated with a convergent Neumann series. These results are important for deriving analytic models of finger-like hydraulic fractures that are consistent with linear elastic fracture mechanics. Submitted to Journal of Elasticity on February 5, 2007. Re-submitted with revisions on May 30, 2007.     

Initialization of phase-field fracture propagation in porous media using probability maps of fracture networks.

It is well known in the geophysical community that surface deflection information/micro-seismic data are considered to be one of the best diagnostics for revealing the volume of rock fracture. However, the in-exactness of the data representing the deformation induced to calibrate and represent complex fracture networks created and connected during hydraulic fracturing presents a challenge. In this paper, we propose a technique that implements a phase-field approach to propagate fractures and their interaction with existing fracture networks using surface deflection data. The latter one provides a probability map of fractures in a heterogeneous reservoir. These data are used to initialize both the location of the fractures and the phase-field function. In addition, this approach has the potential for optimizing well placement/spacing for fluid-filled fracture propagation for oil and gas production and or carbon sequestration and utilization. Using prototype models based on realistic field data, we demonstrate the effects of interactions between existing and propagating fractures in terms of several numerical simulations with different probability thresholds, locations, and numbers of fractures. Our results indicate that propagating fractures interact in a complex manner with the existing fracture network. The modeled propagation of hydraulic fractures is sensitive to the threshold employed within the phase-field approach for delineating fractures.     

Atomic distributions in acetylene-air flame using hydraulic high-pressure nebulization with direct (100%) introduction of solutions Applications to speciation analysis

One of the fundamental factors of the performance of atomic spectrometric methods is the efficiency of sample introduction into flame or plasma. By utilization of the formerly developed hydraulic high-pressure nebulizer, a nebulizer/burner system with solution uptake efficiency of 100% have been worked out. Optimizing operation parameters of nebulizer/burner system, an improvement of 2-12 times was achieved for the signal-to-noise ratio in the flame emission and flame atomic absorption spectrometry, depending on sample flow rate. This nebulizer is especially suitable for development of liquid chromatography-AAS/FES coupled technique for speciation analytical tasks.     

空气在二甲基硅油和液压油中的溶解度

对于诸多工程运用场合, 获得空气在硅油以及液压油中溶解度可靠的数据至关重要. 针对已有测量装置及方法的不足, 建立了一种基于理想气体状态方程来确定气体溶解量的新型精密活塞式装置. 获得了温度为293.2及353.2 K, 压力在0-350 kPa范围内, 空气在500cSt 二甲基硅油中的本生溶解度表达式. 测量了298.2 K时20cSt二甲基硅油及国产32#抗磨液压油在多种气相压力下的本生溶解度. 精度及可靠性分析表明实验数据的误差范围为6%. 本生溶解度与气相压力呈较好的线性关系, 以摩尔分数表示的溶解度与压力呈非线性关系, 但可用Krichevsky-Ilinskaya方程拟合. 发现空气在相对分子质量差异很大的两种二甲基硅油中的本生溶解度很接近, 由此提出, 对于小分子的非极性溶质在聚合物溶剂中的溶解度, 用聚合物单体的摩尔数而不是聚合物分子摩尔数来表示摩尔浓度更有利于实验数据的外推和工程应用. 对于相对分子质量差别较大或无法确定相对分子质量的溶剂, 工程应用中适宜采用本生溶解度.     

Study of an alternative material to manufacture layered hydraulic hoses

Hydraulic hoses are components of umbilical cables and others subsea equipments. They are manufactured from thermoplastic polymers and are susceptible to collapse under external pressure, which can cause plastic strains around the circumference, leading to failure under internal pressure (bursting). This work studies an alternative hydraulic hose liner capable of support such load history, even after long time exposure to the hydraulic fluid. It is based on the comparison between the material currently used (Polyamide 11) and a fluorinated elastomer, Viton^®. Mechanical characterization, ageing tests as well as nonlinear finite elements simulations were accomplished to issue both performances. The results obtained showed that Viton^® liners are mechanically more suitable than Polyamide 11 liners to such hoses. The ageing tests showed compatibility between Viton^® and the hydraulic fluid. Considering that the external aramid layer is responsible to withstand the internal pressure in both cases, Viton^® can successfully replace Polyamide 11 for this application as well as others involving layered hoses under combined internal and external pressure.     

Gradient method of optimal control applied to the operation of a dam water gate

An extension of the authors' previous methods is presented for the optimal control of flood propagation via a dam gate, based on a combination of the finite element and gradient methods. It is assumed in previous papers that the control duration is the same as the duration of the flood. However, the duration of the control does not necessarily coincide with that of the flood flow. To overcome this difficulty, the gradient method is applied to solve the free terminal time-fixed terminal condition problem. It is shown that the water elevation can be controlled exactly the same as with the previously presented method. It is also shown that the computation can be terminated at a far shorter time than the terminal time of the flood.